Just in case of bad eyes:
https://wiki.friendlyelec.com/wiki/images/archive/1/15/20240304102745%21CM3588_NAS_SDK_2309_SCH.PDF - Page 16: GPIO

Best regards,
HP

dwhdmi-rockchip fdea0000.hdmi: i2c read err! dwhdmi-rockchip fdea0000.hdmi: unsupported transfer 1/1, no data Anyone else get the above messages multiple times on Dmesg output ? I dont use the hdmi in or out on my nas kit as its just a nas Nope. I used: $ dmesg | grep "dwhdmi-rockchip fdea0000...

Just bought a new board, installed 4 SSD, loaded the OMV img to an SSD to flasher the eMMC. Connected the board to power and HDMI and the only thing I get is the lights for SSD 2 and 3 flash green three times and go out. Nothing else happens. I press the power button and this process repeats. I don...

Anyone managed to do this? I believe a desktop PSU needs some feedback from the board to actually power on. Search for "Power Good" signal on the main connector going to a desktop PC the mother board. Usually, you find a tiny "jumper" wire or even a "paper clip" stuck ...

Hi everyone, I was following the guide by dukechocula here https://github.com/DukeChocula/CM3588 Ive also tried following the friendlyelec wiki for debian and OMV installs. The wiki is very comprehensive but also confusing for a newbie. The board is powered by a 12V/4A supply, theres plenty of powe...

Where's the boot information? Things like: - How to build U-Boot - How to install it (how it's found, in which order various devices are tried to find the cmd.boot file, ...). - What's supported by the U-Boot build (is it supposed to show something on HDMI, if not why not? Does it support USB keybo...

Last year i bought a CM3588 board along with a 12V 2A power supply. I set it up and installed 2 NVMEs. Last week when i powered it on it doesn't boot. The only things i see are the red power LED, The SYS LED on the processor that constantly blinks and the LED1 and LED2 along with NVMEs' LEDs that b...

Hi Otisamity, Thanks for your reply: If you have access to an oscilloscope, use it to check the signal integrity of your UART lines. Look for noise, distortion, or incorrect voltage levels. Well, I will try this option when possible to access an oscilloscope (could take me weeks before so...) Else, ...

Hi, After a reboot the openwrt shows that the WAN link is 2.5GbE. After a few hours it shows 1GBE. This is very weird. Can the customer support explain this behavior? I faced similar behaviour years ago with 1 GbE network setup at home and after many months I discovered that I had two problems: - On...

Hi, Have a look at these links: - https://wiki.friendlyelec.com/wiki/images/archive/3/37/20231128105652%21CM3588_Pinout_Interfaces.pdf - https://wiki.friendlyelec.com/wiki/images/3/37/CM3588_Pinout_Interfaces.pdf - https://wiki.friendlyelec.com/wiki/images/e/ee/Rockchip_RK3588_Datasheet_V1.6-2023101...

Hi, I am also interested to give a try to Proxmox, some time in the future when able to buy another CM3588. Just wanted to update that it seems they have referenced a beta for Proxmox using kernel 6.1.1 on the wiki and I found it on the downloads page. Going to try it out. https://wiki.friendlyelec....

Exact same problem here. After rebooting the board I only get a blinking cursor on the top left corner after the friendlyelec logo. Same led lights. Inserting the installation sd seems to do nothing,. Help is much appreciated! I had the same symptoms about LEDs and blinking cursor in top left corne...

Smilar problem. Ordered a new CB3588 Plus and new out of box, it won't power on. Have tried two power supplies with no change. I have no led's and the fan I installed doesn't run. I have tried with all 4 drives, just 1 drive and all drives removed. Same issue. Any suggestions? Thanks. Some suggesti...

Hi, mine has done that a few times , i had to re-install the OS to the EMMC Well, I faced similar issue today after editing the '/etc/fstab' and '/etc/crypttab' files from the eMMC drive embedded with the CPU, after setting up LUKS on the NVME SSDs. I solved the problem by putting Debian Desktop ima...

Hi everyone, I am a pretty happy owner of a CM3588 system with 4 NVME SSD drives. I am facing the same problem: "Garbage" on terminal screen at boot time. I expected 115,200 bps 8 N 1 like most of the time and I had to try everything possible without success. I just tried a manual input wi...