FriendlyELEC-Forum

Tanat wrote:
Now I have a new problem with ubuntu_core_4.11_20170531 on NanoPi NEO Air.
After connect camera CAM500B to the board and load ubuntu_core_4.11 I don't see device video0.

Hi，
Now the mainline kernel has already support ffmpeg, but now don't support DVP driver.

thank you！

Hi, Did any of You guys run the NanoPi NEO with FriendlyArm Matrix 2'8 SPI Key TFT Touch 240x320 LCD? I've tried this: http://wiki.friendlyarm.com/wiki/index.php/Matrix_-_2%278_SPI_Key_TFT#Display_Debian_GUI_on_2.8.22LCD but it does'nt work. I have folowing error message: "modprobe: ERROR: cou...

I am also looking for this. I would like a simple pcb with two style A usb connectors which plug into the expansion header. Maybe I must make my own? Anyone interested in this? Hi, If you need a customized service you can send email to FriendlyElc technical support mailbox :techsupport@friendlyarm....

There doesn't seem to be much info regarding which image to go for. http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO2#Make_an_Installation_TF_Card suggests flashing the ubuntu image by default but there's also a debian image which at the time of writing is slightly more recent than ubuntu. So ...

Hi,
The NOE runs ubuntu16.04 so if you want to use ppp support you can just search Ubuntu16.04 how to configure PPP will be ok, and you can look at this link: https://wiki.archlinux.org/index.php/NetworkManager.

thank you!

Hi, Do you have successfully logged in or not via ssh? Login via SSH The NanoPi NEO doesn't have a video output interface. You can log into the board via SSH. In our test the IP address detected by our router was 192.168.1.230 and we ran the following command to log into the NanoPi NEO: $ ssh root@1...

You can refer to the follow image to connect a audio:

Then you can use these two commands to test it :
#arecord -D hw：0,0 -f cd test.wav
#aplay test.wav

ProblemTestCan't Recognize the Device 1、It must use the nas dock ROM 2、Try to make a new SD card again to test 3、Format the hard disk to test again 4、Under the Linux system to format and fdisk the hard disk then test again 5、Troubleshoot the USB problem of the NanoPi NEO/NEO2 board: a. Check whether...

omidttl wrote:
how we can erase the emmc ??
tnks

You can use a 'dd' command to erase emmc.
Such as: dd if=/dev/zero of=emmc partition bs=16M count=4

thank you!

I tried to install latest version of OS(Ubuntu 16.04 LTS) from Mediafire and now I can run nmcli but still can not connect to any wifi network when I do scanning there is no wifi network on the list, I configured the wpa_supplicant too but still, can not connect.help me Hi, Please refer to the wiki...

rozpruwacz wrote:
Hi,

are there plans to support PCM5102A NanoHat in mainline kernel ?

Marek

Hi,
Now the mainline kernel already has support for the NanoHat PCM5102A. We will release it very soon please pay attention to the wiki page .

thank you!

tadvi, w0lt, peabody1929, Cephas486, Pablo0208, ctbarker32, Ronnie: You all ordered the NAS Dock and NanoPi Neo with Pin Headers Soldered? Hi， I suspect that the problem is caused by the insecure soldering on the development board around the GPIO pins. thank you! You mean the header pins soldering ...

Hi， There is a possibility under this circumstances is that the connection pin on the NEO/NEO2 board is having an insecure soldering so the USB device is not detected. The NAS was checked before out of the factory. Could you guys solder the CPU board Pins again then test the nas dock again? thank y...

Hi， There is a possibility under this circumstances is that the connection pin on the NEO/NEO2 board is having an insecure soldering so the USB device is not detected. The NAS was checked before out of the factory. Could you guys solder the CPU board Pins again then test the nas dock again? thank you!

Hi ,
You can download the schematic from wiki:http://wiki.friendlyarm.com/wiki/index.php/Main_Page#Hats.26Docks

thank you!

Hi,
Could you give the dmesg information to me ? Do the terminal show any information when booting the NEO2?

Thank you!

every time I try to shutdown nanopi neo air i get the following kernel panic. I can confirm everything except shutting down works(wifi,bluetooth,gpio,...) except eflasher and eMMC. here... is the important part: root@FriendlyARM:~# shutdown -h now [ 135.256708] ------------[ cut here ]------------ ...

Hi,thanks for your replay. I am using http://www.mediafire.com/file/htxrod8bux2xmh1/nanopi-air-eflasher-sd8g-20170220.img.zip on the sd card i can confirm there is a friendlyarm partition on sd card containing rootfs and all related files to be flashed. the main problem is when i use eflasher it ca...

Oh, "Now" it doesn't have support for MATE. Chensy said it wasn't developed for my device at all. Silly me, I believed him because I can't find a copy anywhere on the internet. Will you be removing the postings of mate support like you removed all traces of a downloadable copy of mate fro...

Hi,
You cannot external power button on M3 , the hardware doesnot support it.

thank you!

Hi ,
The NEO has supported mainline ubuntu core you can download it from NEO'wiki .

thank you!

The hardware specs pretty clearly state ubuntu-MATE. But yes, when I went to download the actual OS it wasn't present. Is it even in the works? Links to reference of MATE http://www.friendlyarm.com/index.php?route=product/product&product_id=176 http://wiki.friendlyarm.com/wiki/index.php/NanoPi_...

Hi All,

About the Hardware_Differences_Among_Different_Versions of the NanoPi NEO , you can see this link which has detailed introduction : http://wiki.friendlyarm.com/wiki/index. ... t_Versions

thank you!

Hi， You can use the gpio VDD_5V: 5V power input/output to supply the power, When the external device’s power is greater than the MicroUSB’s the external device is charging the board , then you can use the otg function, otherwise the board powers the external device.The input range is 4.7V ~ 5.6V. th...

Hi, The image has supported the AP mode , you can refer to the following steps to setup and configure it . $ turn-wifi-into-apmode yes Enter wireless name [default: friendlyelec-wifiap]: Enter password [default: 123456789]: Configuration Saved! Please connect your computer to the wireless network: W...

Hello, Is there a device tree blog (.dtb) file that comes with the NanoPi Neo or NanoPi Air. How is the hardware mapping selected in the default IMG file ? Where is the selection of hardware module is made ? (Ex: UART on pin xyz, SPI on pins xyz, etc..) Thanks ssinfod Hi, Now we are working on it ,...

Hello. I previously used matrix github on nanopi neo for infra red purposes. On nanopi neo air i would like to do the same. But it seems the matrix git has changed and now the shared object most of the examples rely on is missing. Libfahw.so. Could you please update the matrix git and provide the m...

It appears that the 5102 HAT uses pin 6 GPIOL11 (363) of the nanopi for Infra Red purposes, like the allwinner H3 datasheet suggests. However, I cannot get this to work with the matrix demo example. I changed the pin number in this example to the right value (from 203 to 363) but still no luck. The...

Hi , About how to use 5102 you can see the wiki :http://wiki.friendlyarm.com/wiki/index.php/Matrix_-_NanoHat_PCM5102A/ that web page has detailed steps. If you want to use another Alsa output, you can refer to the follow image. You can use this command to record: #arecord -D hw：0,0 -f cd test.wav an...

Hi， Debian system's default audio output is the 3.5mm audio jack. You can turn on the HDMI audio by editing the /etc/asound.conf file: pcm.!default { type hw card 1 device 0 } ctl.!default { type hw card 1 } card 0 points to the 3.5mm audio jack and card 1 points to the HDMI audio. You need to save ...

Our system has support for popular USB WiFi drivers. Many USB WiFi modules are plug and play with our system. Here is a list of models we tested; Number Model 1 RTL8188CUS/8188EU 802.11n WLAN Adapter 2 RT2070 Wireless Adapter 3 RT2870/RT3070 Wireless Adapter 4 RTL8192CU Wireless Adapter 5 MI WiFi mt...

Hi Mindee, Thanks for your reply :) I was looking further and I found that Neo Air has 0.5mm pitch 24Pin FPC connector. And I am thinking of using CAM500B 5MP 1080p Camera Module with OV5640 Chip - my question - is the FPC supplied with CAM500B has the same pitch and can be used directly without an...

Hi, You can refer to the following configuration to test : H3 sys_config.fex Configuration Directives （About cvbs） 1、[boot_disp] Configuration： Configuration Directives adver_disp： 0:do not hotplud for lcd; 1:need hotplud for hdmi/tv auto_hpd： Supports hot plug detect configuration; (1:support 0:don...

H3 sys_config.fex Configuration Directives （About cvbs） 1、[boot_disp] Configuration： Configuration Directives adver_disp： 0:do not hotplud for lcd; 1:need hotplud for hdmi/tv auto_hpd： Supports hot plug detect configuration; (1:support 0:donot) output_type： Displays output to the default configurati...

Hi all,
You can refer to this video that introduce how to flash the image to eMMC:https://www.youtube.com/watch?v=Jy2YX8FSo9s&t=2s

thank you!

Hi All I want to compile github driver source for realtek RTL8723BU module. since it needs linux source , I have downloaded friendlyarm linux-3.4.49 from github to /usr/src then edit Makefile and adjust KSRC to /usr/src/linux-3.4.49 and KVER to $(uname -r) and MODDESTDIR to /lib/modules/3.4.49-s5p4...

So I can't update it will say this: Error writing to output file - write (28: No space left on device) It has 8GB of eMMC. Here is a df -h command to show it. root@FriendlyARM:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/root 886M 886M 0 100% / devtmpfs 168M 0 168M 0% /dev tmpfs 248M 0 ...

IGOR wrote:
How to connect USB Camera to Nano M2 via USB port in Android?
Should I have root-rights or no?

Hi，
You need to compile the kernel to support USB camera.

thank you！

After doing (in my case): sudo umount /dev/sdb (result) umount: /dev/sdb: not mounted sudo parted /dev/sdb unit % resizepart 2 100 unit MB print Warning: Partition /dev/sdb2 is being used. Are you sure you want to continue? parted: invalid token: 100 Yes/No? Does one ignore both warnings? Hi , When...

Could you please provide a walk through on how to resize the partition on the M1 image I found on Media Fire There is no info on the M1 Wiki page, and the walk through described on the M2 wiki process DOES NOT WORK! I realize that the unit is very new, and accept some stumbles to begin with, but pl...

Hi, sorry for all the questions, perhaps you should add them to your wiki? How do I change the screen res on the Debian build, I have 720p and I want 1080p Are there any OpenGLES2.0 libs installed on the M1/M2/Pi2? What is the SSH passwords for connecting with VisualGDB NanoPi2/fa does not work Hop...

I need to test the CAM500 module on M2 but current Debian is outdated and it does not have support for the camera. I have rebuild the kernel with support for the OV5640, the camera module is identified but no /dev/video0 is created. [ 2.148000] gspca_main: v2.14.0 registered [ 2.152000] nxp_v4l2_pr...

I have followed the instruction on how to develop and complile a embedded application but cant not get the crosscompiler to work Host: ubuntu 16.10 latest on 64bit intel The error I get is that libts and zlib is missing. Libts I cant find on my host, zlib I found n the toolchain downloaded. While s...

Sorry, i read and see " If you want to generate an image file that can be flashed to eMMC you need to generate a boot.img file and copy it to your installation SD card". Maybe it only with some nanopi boot with eMMC? What's about nanopi fire2, it boot from sdcard? what must we do to add m...

Is there a set of pins or through holes like on the RPi to setup a reset button? Board is not recognizing reboot command and just sits there after killing processes. Would like to install a reset for situations of rebooting. Hi， The board integrates reset button that you can read the wiki or web pa...

Hello, I have tried running debian and armbian. I can log in via ssh but I have tried two different monitors with no success. I have tried setting different resolutions on armbian with h3disp. on Debian xrandr I get "Can't open display" Monitor recognises the cable being plugged in but ju...

Hi there, I just built the matrix code because I would like to try the oled functionality it provides. I needed to change the pin numbers from 7 (203) and 11 (0) to 13 (2) and 15 (3) because I already use these pins for other purposes. It builds fine but when I execute the generated module it compl...

Hello all, I have just got my NanoPi Neo Air board and was trying to setup Wireless connection as written in wiki but i am unable to get it working at all. Router: NetGear R6300 (WPA2-Personal security) Board: NanoPi Neo Air Image: nanopi-air-core-qte-sd4g.img.zip Reference: http://wiki.friendlyarm...

VALERYRAMIREZ wrote:
Good afternoom everyone, which IDE do yo recommend for developing applications and to control hardware pins on the nanopi M1?.

Hi，
Any ide will do.

thank you!

Good morning Jimm, thank you for your answer, can you help me with some documentation about it, I also have another question, I've been looking the API (its in chinesse) and I'm asking if it is possible to develop on linux without using the API, I mean, I 'd like to configure the peripherals by mys...

Search found 156 matches