Code: Select all
€ ے € ü ہ à چ،پ¥حپ‰ة½•¹±پچ±•…ة5)ف…رچ،‘½پر¥µ•ةپحر…ةر5)5))ف½ة¥¹پر½پ……ةچ،حة5)ف…¥ر¥¹پ™½ةپء±±پچ،…¹•¹¹5)ے
--------------------------------------------------------------------------------
Second Boot by Nexell Co. : Ver0.3.6 - Built on Jun 29 2016 15:19:53
--------------------------------------------------------------------------------
DDR3 POR Init Start 0
Lock value = 191
GATE CYC = 0x00000492
GATE CODE = 0x00000000
Read DQ = 0x08080808
Write DQ = 0x08080808
DDR3 Init Done!
CCI Init!
Wakeup CPU Wakeup Sub CPU 1234567
CPU Wakeup done! WFI is expected.
CPU0 is Master!
Loading from sdmmc...
Image Loading Done!
Launch to 0x42C00000
U-Boot 2014.07-g87a83ca (Mar 24 2017 - 19:33:41)
PLL : [0] = 800000000, [1] = 800000000, [2] = 614394000, [3] = 800000000
(0) PLL1: CPU FCLK = 800000000, HCLK = 200000000 (G0)
(7) PLL1: CPU FCLK = 800000000, HCLK = 200000000 (G1)
(2) PLL3: MEM FCLK = 800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
(1) PLL0: BUS BCLK = 400000000, PCLK = 200000000
(8) PLL0: CCI4 BCLK = 400000000, PCLK = 200000000
(3) PLL0: G3D BCLK = 400000000
(4) PLL0: CODA BCLK = 400000000, PCLK = 200000000
(5) PLL0: DISP BCLK = 400000000, PCLK = 200000000
(6) PLL0: HDMI PCLK = 100000000
I2C: ready
DRAM: 256 MiB
Heap = 0x43000000~0x45000000
Code = 0x42c00000~0x42c75984
GLD = 0x42bffeb8
GLBD = 0x42bffe68
SP = 0x42bffe68,0x42bffe50(CURR)
PC = 0x42c06220
TAGS = 0x40000100
PAGE = 0x42c80000~0x42c8c000
MACH = [4330]
VER = 0
BOARD= [nanopi3]
LCD = N/A (-1)
MMC: NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc0 is current device
Writing to MMC(0)... done
HDMI: display.0, preset 0 (1280 * 720)
HDMI: PHY Ready!!!
DONE: Logo bmp 800 by 480 (3bpp), len=1152056
DRAW: 0x47000000 -> 0x46000000
Hit any key to stop autoboot: 1 0
## Booting kernel from Legacy Image at 48000000 ...
Image Name: Linux-3.4.39-FriendlyARM
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4627360 Bytes = 4.4 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.39-FriendlyARM (root@jensen) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #1 SMP PREEMPT Wed Mar 1 14:07:39 HKT 2017
[ 0.000000] CPU: ARMv7 Processor [410fd033] revision 3 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: NANOPI3
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Display: HDMI selected
[ 0.000000] nxp_reserve_mem: reserve CMA: size 167772160
[ 0.000000] NXP/CMA: Reserved 0x65600000/0x0a000000 for 'ion'
[ 0.000000] NXP/CMA: success register cma region for 'ion'
[ 0.000000] rquest persistent memory from 655fc000 (00000000)-00004000
[ 0.000000] Initialized persistent memory from 655fc000-655fffff
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[ 0.000000] CPU : iomap[ 1]: p 0xe0000000 -> v 0xf0300000 len=0x100000
[ 0.000000] CPU : iomap[ 2]: p 0xfff00000 -> v 0xf0400000 len=0x100000
[ 0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[ 0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[ 0.000000] CPU : DMA Zone Size =16M, CORE 8
[ 0.000000] s5p6818-NanoPi3: Board initialized
[ 0.000000] CPU : Clock Generator= 58 EA, DVFS = support, PLL.1
[ 0.000000] PLL : [0] = 800000000, [1] = 800000000, [2] = 614394000, [3] = 800000000
[ 0.000000] (0) PLL1: CPU FCLK = 800000000, HCLK = 200000000 (G0)
[ 0.000000] (7) PLL1: CPU FCLK = 800000000, HCLK = 200000000 (G1)
[ 0.000000] (2) PLL3: MEM FCLK = 800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[ 0.000000] (1) PLL0: BUS BCLK = 400000000, PCLK = 200000000
[ 0.000000] (8) PLL0: CCI4 BCLK = 400000000, PCLK = 200000000
[ 0.000000] (3) PLL0: G3D BCLK = 400000000
[ 0.000000] (4) PLL0: CODA BCLK = 400000000, PCLK = 200000000
[ 0.000000] (5) PLL0: DISP BCLK = 400000000, PCLK = 200000000
[ 0.000000] (6) PLL0: HDMI PCLK = 100000000
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1316000 s12608 r8192 d16064 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
[ 0.000000] Kernel command line: console=ttySAC0,115200n8 androidboot.console=ttySAC0 androidboot.serialno=0123456789abcdef initrd=0x49000000,0x100000 lcd=HDMI720P60
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] allocated 2097152 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 1024MB = 1024MB total
[ 0.000000] Memory: 861004k/861004k available, 187572k reserved, 272384K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xef800000 - 0xfee00000 ( 246 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef600000 ( 758 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0870d28 (8612 kB)
[ 0.000000] .init : 0xc0871000 - 0xc08a8140 ( 221 kB)
[ 0.000000] .data : 0xc08aa000 - 0xc0925c30 ( 496 kB)
[ 0.000000] .bss : 0xc0925c54 - 0xc0b08da0 (1933 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:272
[ 0.000000] GIC @f0009000: start 0 (gic 31)
[ 0.000000] GPIO @f001a000: start 106, mask 0xffffffff (gpio 85)
[ 0.000000] GPIO @f001b000: start 138, mask 0xffffffff (gpio 86)
[ 0.000000] GPIO @f001c000: start 170, mask 0xffffffff (gpio 87)
[ 0.000000] GPIO @f001d000: start 202, mask 0xffffffff (gpio 88)
[ 0.000000] GPIO @f001e000: start 234, mask 0xffffffff (gpio 89)
[ 0.000000] ALIVE @f0010800: start 266, mask 0x000000ff (alive 36, num 6)
[ 0.000000] timer.0: source, 10000000(HZ:250), mult:3355443200
[ 0.000000] timer.1: event , 10000000(HZ:250), mult:42949673
[ 0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
[ 0.000000] Calibrating delay loop... 1594.36 BogoMIPS (lpj=3188736)
[ 0.048000] pid_max: default: 32768 minimum: 301
[ 0.048000] Security Framework initialized
[ 0.048000] SELinux: Initializing.
[ 0.048000] Mount-cache hash table entries: 512
[ 0.048000] Initializing cgroup subsys debug
[ 0.048000] Initializing cgroup subsys cpuacct
[ 0.048000] Initializing cgroup subsys memory
[ 0.048000] Initializing cgroup subsys freezer
[ 0.048000] CPU: Testing write buffer coherency: ok
[ 0.048000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.048000] hw perfevents: no hardware support available
[ 0.048000] Setting up static identity map for 0x40617400 - 0x40617458
[ 0.096000] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.136000] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.172000] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.216000] CPU4: thread -1, cpu 0, socket 4, mpidr 80040400
[ 0.256000] CPU5: thread -1, cpu 1, socket 4, mpidr 80040401
[ 0.296000] CPU6: thread -1, cpu 2, socket 4, mpidr 80040402
[ 0.336000] CPU7: thread -1, cpu 3, socket 4, mpidr 80040403
[ 0.336000] Brought up 8 CPUs
[ 0.336000] SMP: Total of 8 processors activated (12754.94 BogoMIPS).
[ 0.344000] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 3
[ 0.344000] pwm: max = 50000000 hz
[ 0.344000] prepare_gpio_suspend:
[ 0.344000] alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[ 0.344000] alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[ 0.344000] alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[ 0.344000] alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[ 0.344000] alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[ 0.348000] dummy:
[ 0.348000] NET: Registered protocol family 16
[ 0.348000] persistent_ram: uncorrectable error in header
[ 0.348000] persistent_ram: no valid data in buffer (sig = 0xffffffff)
[ 0.360000] console [ram-1] enabled
[ 0.360000] [Register machine platform devices]
[ 0.360000] mach: add amba device pl08xdmac.0
[ 0.360000] mach: add amba device pl08xdmac.1
[ 0.360000] mach: add device uart0
[ 0.360000] mach: add device uart1
[ 0.360000] mach: add device uart2
[ 0.360000] mach: add device uart3
[ 0.364000] mach: add device uart4
[ 0.364000] mach: add device syncgen [2]
[ 0.364000] mach: add device lcd
[ 0.364000] mach: add device i2c bus (array:3)
[ 0.364000] mach: add device Real Time Clock
[ 0.364000] mach: add device generic pwm (array:4)
[ 0.364000] mach: add device generic gpio (array:6)
[ 0.364000] mach: add device i2s (array:1)
[ 0.364000] mach: add device spdif tx
[ 0.364000] mach: add device usb_ehci
[ 0.364000] mach: add device usb_ohci
[ 0.364000] mach: add device usb otg
[ 0.364000] mach: add device ion-nxp
[ 0.368000] mach: add graphic device opengl|es
[ 0.368000] [Register board platform devices]
[ 0.368000] plat: board revision 7
[ 0.368000] plat: add dynamic frequency (pll.1)
[ 0.368000] plat: add device TMU
[ 0.368000] plat: add framebuffer
[ 0.368000] plat: boot from mmc.0
[ 0.368000] plat: add device sdmmc [0]
[ 0.368000] plat: add device sdmmc [1]
[ 0.368000] plat: add backlight pwm device
[ 0.368000] plat: add device keypad
[ 0.368000] plat: add device spdif playback
[ 0.368000] plat: add device asoc-es8316
[ 0.372000] plat: add device nxp-v4l2
[ 0.372000] plat: register spidev
[ 0.372000] plat: add touch(ft5x0x) device
[ 0.372000] plat: add touch(goodix) device
[ 0.372000] plat: goodix: irq=186 (80)
[ 0.372000] plat: add touch(himax) device
[ 0.372000] plat: add touch(it7260) device
[ 0.372000] plat: add onewire ts device
[ 0.376000] plat: add iio adc device
[ 0.376000] plat: add device hdmi-cec
[ 0.376000] plat: add device nxp-gmac
[ 0.376000] plat: add device gpio_led
[ 0.376000]
[ 0.376000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.376000] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.400000] bio: create slab <bio-0> at 0
[ 0.400000] gpiochip_add: registered GPIOs 0 to 31 on device: GPIOA
[ 0.400000] gpiochip_add: registered GPIOs 32 to 63 on device: GPIOB
[ 0.400000] gpiochip_add: registered GPIOs 64 to 95 on device: GPIOC
[ 0.400000] gpiochip_add: registered GPIOs 96 to 127 on device: GPIOD
[ 0.400000] gpiochip_add: registered GPIOs 128 to 159 on device: GPIOE
[ 0.400000] gpiochip_add: registered GPIOs 160 to 165 on device: GPIOALV
[ 0.400000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[ 0.400000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[ 0.400000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[ 0.404000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 33
[ 0.404000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[ 0.404000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[ 0.404000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[ 0.404000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 34
[ 0.404000] nxp_ion_probe success!!!
[ 0.404000] SCSI subsystem initialized
[ 0.404000] usbcore: registered new interface driver usbfs
[ 0.408000] usbcore: registered new interface driver hub
[ 0.408000] usbcore: registered new device driver usb
[ 0.408000] i2c-gpio i2c-gpio.3: using pins 159 (SDA) and 158 (SCL)
[ 0.408000] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.408000] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.408000] s3c-i2c s3c2440-i2c.0: bus frequency set to 390 KHz
[ 0.408000] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.408000] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.408000] s3c-i2c s3c2440-i2c.1: bus frequency set to 97 KHz
[ 0.412000] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.412000] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 0.412000] s3c-i2c s3c2440-i2c.2: bus frequency set to 195 KHz
[ 0.412000] Linux media interface: v0.10
[ 0.412000] Linux video capture interface: v2.00
[ 0.412000] pps_core: LinuxPPS API ver. 1 registered
[ 0.412000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.412000] PTP clock support registered
[ 0.420000] axp_mfd 3-0034: AXP (CHIP ID: 0x06) detected
[ 0.424000] axp22_ldo1: 3000 mV
[ 0.428000] axp22_aldo1: 700 <--> 3300 mV at 3300 mV
[ 0.432000] axp22_aldo2: 700 <--> 3300 mV at 1800 mV
[ 0.436000] axp22_aldo3: 700 <--> 3300 mV at 1000 mV
[ 0.440000] axp22_dldo1: 700 <--> 3300 mV at 3300 mV
[ 0.444000] axp22_dldo2: No configuration
[ 0.444000] axp22_dldo2: 700 <--> 3300 mV at 700 mV
[ 0.444000] axp22_dldo3: No configuration
[ 0.448000] axp22_dldo3: 700 <--> 3300 mV at 700 mV
[ 0.448000] axp22_dldo4: No configuration
[ 0.448000] axp22_dldo4: 700 <--> 3300 mV at 700 mV
[ 0.452000] axp22_eldo1: 700 <--> 3300 mV at 1800 mV
[ 0.460000] axp22_eldo2: 700 <--> 3300 mV at 3300 mV
[ 0.460000] axp22_eldo3: No configuration
[ 0.464000] axp22_eldo3: 700 <--> 3300 mV at 700 mV
[ 0.464000] axp22_dc5ldo: No configuration
[ 0.464000] axp22_dc5ldo: 700 <--> 1400 mV at 1200 mV
[ 0.468000] axp22_dcdc1: 1600 <--> 3400 mV at 3300 mV
[ 0.476000] axp22_dcdc2: 600 <--> 1540 mV at 1200 mV
[ 0.480000] axp22_dcdc3: 600 <--> 1860 mV at 1200 mV
[ 0.484000] axp22_dcdc4: 600 <--> 1540 mV at 1500 mV
[ 0.488000] axp22_dcdc5: 1000 <--> 2550 mV at 1500 mV
[ 0.492000] axp22_ldoio0: 700 <--> 3300 mV at 3800 mV
[ 0.492000] axp22_ldoio1: 700 <--> 3300 mV at 3800 mV
[ 0.496000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.496000] Bluetooth: Core ver 2.19
[ 0.496000] NET: Registered protocol family 31
[ 0.496000] Bluetooth: HCI device and connection manager initialized
[ 0.496000] Bluetooth: HCI socket layer initialized
[ 0.496000] Bluetooth: L2CAP socket layer initialized
[ 0.496000] Bluetooth: SCO socket layer initialized
[ 0.496000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.496000] Switching to clocksource source timer
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Could not switch to high resolution mode on CPU 7
[ 0.500000] dummy_timer is not functional.
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Could not switch to high resolution mode on CPU 4
[ 0.500000] Could not switch to high resolution mode on CPU 6
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Could not switch to high resolution mode on CPU 5
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Could not switch to high resolution mode on CPU 2
[ 0.500000] Could not switch to high resolution mode on CPU 1
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Could not switch to high resolution mode on CPU 3
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Could not switch to high resolution mode on CPU 0
[ 0.516000] NET: Registered protocol family 2
[ 0.516000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.516000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.520000] TCP bind hash table entries: 65536 (order: 8, 1572864 bytes)
[ 0.520000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.520000] TCP: reno registered
[ 0.520000] UDP hash table entries: 512 (order: 3, 32768 bytes)
[ 0.520000] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes)
[ 0.520000] NET: Registered protocol family 1
[ 0.520000] RPC: Registered named UNIX socket transport module.
[ 0.520000] RPC: Registered udp transport module.
[ 0.520000] RPC: Registered tcp transport module.
[ 0.520000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.520000] Unpacking initramfs...
[ 0.560000] Initramfs unpacking failed: junk in compressed archive
[ 0.564000] Freeing initrd memory: 1024K
[ 0.564000] Disply Reset Status : On
[ 0.564000] Display LCD register operation
[ 0.564000] Display.0 fps=45 (22 ms), wait= 8 jiffies, Pixelclk=43885285hz
[ 0.564000] LCD : [1]=LCD connect to [6]=SYNCGEN0
[ 0.564000] bt_bcm: rfkill initialized
[ 0.564000] audit: initializing netlink socket (disabled)
[ 0.564000] type=2000 audit(0.560:1): initialized
[ 0.564000] highmem bounce pool size: 64 pages
[ 0.576000] NFS: Registering the id_resolver key type
[ 0.576000] fuse init (API version 7.18)
[ 0.576000] msgmni has been set to 1151
[ 0.580000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.580000] io scheduler noop registered
[ 0.580000] io scheduler deadline registered
[ 0.580000] io scheduler cfq registered (default)
[ 0.580000] display.0 connected to fb.0 ...
[ 0.580000] nxp-fb.0: dma addr = 0x65600000, buf[0xe49a72c0]
[ 0.580000] nxp-fb.0: dma addr = 0x65984000, buf[0xe49a7480]
[ 0.580000] nxp-fb.0: dma addr = 0x65d08000, buf[0xe49a7640]
[ 0.664000] nxp-fb 0: out[0], 1280 * 720 - 32 bpp (phys:65600000 virt:0xe5600000 max:11059200)
[ 0.664000] nxp-uart.0: ttySAC0 at MMIO 0xc00a1000 (irq = 39) is a S3C6400/10
[ 2.108000] console [ttySAC0] enabled
[ 2.108000] nxp-uart.1: ttySAC1 at MMIO 0xc00a0000 (irq = 38) is a S3C6400/10
[ 2.116000] nxp-uart.2: ttySAC2 at MMIO 0xc00a2000 (irq = 40) is a S3C6400/10
[ 2.124000] nxp-uart.3: ttySAC3 at MMIO 0xc00a3000 (irq = 41) is a S3C6400/10
[ 2.132000] nxp-uart.4: ttySAC4 at MMIO 0xc006d000 (irq = 42) is a S3C6400/10
[ 2.140000] Matirx PWM init
[ 2.140000] iio-adc initialized
[ 2.148000] loop: module loaded
[ 2.148000] tun: Universal TUN/TAP device driver, 1.6
[ 2.152000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.160000] -- nxpmac initialize --
[ 2.160000] stmmac - user ID: 0x37, Synopsys ID: 0x37
[ 2.168000] Ring mode enabled
[ 2.172000] DMA HW capability register supported
[ 2.176000] Enhanced/Alternate descriptors
[ 2.180000] Enabled extended descriptors
[ 2.184000] RX Checksum Offload Engine supported (type 2)
[ 2.188000] TX Checksum insertion supported
[ 2.192000] Wake-Up On Lan supported
[ 2.196000] Enable RX Mitigation via HW Watchdog Timer
[ 2.240000] stmmac: probed
[ 2.240000] eth0: PHY ID 001cc915 at 0 IRQ 257 (stmmac-0:00)
[ 2.244000] eth0: PHY ID 001cc915 at 7 IRQ 257 (stmmac-0:07) active
[ 2.252000] PPP generic driver version 2.4.2
[ 2.256000] PPP BSD Compression module registered
[ 2.260000] PPP Deflate Compression module registered
[ 2.264000] PPP MPPE Compression module registered
[ 2.268000] NET: Registered protocol family 24
[ 2.272000] usbcore: registered new interface driver asix
[ 2.280000] usbcore: registered new interface driver cdc_ether
[ 2.284000] usbcore: registered new interface driver net1080
[ 2.288000] usbcore: registered new interface driver cdc_subset
[ 2.296000] usbcore: registered new interface driver zaurus
[ 2.300000] usbcore: registered new interface driver cdc_ncm
[ 2.308000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.312000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[ 2.320000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[ 2.328000] nxp-ehci nxp-ehci: irq 82, io mem 0xc0030000
[ 2.344000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[ 2.344000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.348000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.356000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[ 2.360000] usb usb1: Manufacturer: Linux 3.4.39-FriendlyARM ehci_hcd
[ 2.368000] usb usb1: SerialNumber: nxp-ehci
[ 2.372000] hub 1-0:1.0: USB hub found
[ 2.376000] hub 1-0:1.0: 3 ports detected
[ 2.380000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 2.584000] Core Release: 2.93a
[ 2.588000] Setting default values for core params
[ 2.588000] Finished setting default values for core params
[ 2.700000] usb 1-1: new high-speed USB device number 2 using nxp-ehci
[ 2.792000] Using Buffer DMA mode
[ 2.792000] Dedicated Tx FIFOs mode
[ 2.796000] dwc_otg dwc_otg: DWC OTG Controller
[ 2.800000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[ 2.808000] dwc_otg dwc_otg: irq 81, io mem 0x00000000
[ 2.812000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.820000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.824000] usb usb2: Product: DWC OTG Controller
[ 2.832000] usb usb2: Manufacturer: Linux 3.4.39-FriendlyARM dwc_otg_hcd
[ 2.832000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610
[ 2.832000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.832000] usb 1-1: Product: USB2.0 Hub
[ 2.832000] hub 1-1:1.0: USB hub found
[ 2.832000] hub 1-1:1.0: 4 ports detected
[ 2.864000] usb usb2: SerialNumber: dwc_otg
[ 2.868000] hub 2-0:1.0: USB hub found
[ 2.872000] hub 2-0:1.0: 1 port detected
[ 2.876000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.880000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[ 2.888000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[ 2.892000] nxp-ohci nxp-ohci: irq 82, io mem 0xc0020000
[ 2.960000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.960000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.968000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[ 2.972000] usb usb3: Manufacturer: Linux 3.4.39-FriendlyARM ohci_hcd
[ 2.980000] usb usb3: SerialNumber: nxp-ohci
[ 2.984000] hub 3-0:1.0: USB hub found
[ 2.988000] hub 3-0:1.0: 3 ports detected
[ 2.992000] Initializing USB Mass Storage driver...
[ 2.996000] usbcore: registered new interface driver usb-storage
[ 3.000000] USB Mass Storage support registered.
[ 3.008000] usbcore: registered new interface driver usbserial
[ 3.012000] usbcore: registered new interface driver usbserial_generic
[ 3.020000] USB Serial support registered for generic
[ 3.024000] usbserial: USB Serial Driver core
[ 3.028000] usbcore: registered new interface driver ch341
[ 3.032000] USB Serial support registered for ch341-uart
[ 3.040000] usbcore: registered new interface driver cp210x
[ 3.044000] USB Serial support registered for cp210x
[ 3.048000] usbcore: registered new interface driver ftdi_sio
[ 3.056000] USB Serial support registered for FTDI USB Serial Device
[ 3.060000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 3.068000] usbcore: registered new interface driver option
[ 3.072000] USB Serial support registered for GSM modem (1-port)
[ 3.080000] usbcore: registered new interface driver pl2303
[ 3.084000] USB Serial support registered for pl2303
[ 3.088000] usbcore: registered new interface driver ti_usb_3410_5052
[ 3.096000] USB Serial support registered for TI USB 3410 1 port adapter
[ 3.104000] USB Serial support registered for TI USB 5052 2 port adapter
[ 3.108000] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
[ 3.116000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 3.124000] android_usb gadget: Number of LUNs=1
[ 3.128000] lun0: LUN: removable file: (no medium)
[ 3.132000] android_usb gadget: android_usb ready
[ 3.136000] mousedev: PS/2 mouse device common for all mice
[ 3.144000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[ 3.148000] usbcore: registered new interface driver xpad
[ 3.156000] i2c-core: driver [IT7260-ts] using legacy suspend method
[ 3.160000] i2c-core: driver [IT7260-ts] using legacy resume method
[ 3.168000] <<-GTP-INFO->> GTP driver installing...
[ 3.172000] himax_ts 2-0048: Unable to get DevId
[ 3.176000] touchscreen-1wire initialized
[ 3.180000] backlight-1wire initialized
[ 3.184000] input: fa_ts_input as /devices/virtual/input/input1
[ 3.192000] ts-if initialized
[ 3.192000] [RTC] day=2016.01.01 time=08:00:00
[ 3.196000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[ 3.204000] i2c /dev entries driver
[ 3.208000] ...................................ov5640_probe 2234
[ 3.212000] ...................................ov5640_video_probe 2193
[ 3.220000] ov5640 0-003c: reg_read: i2c read error, reg: 300a
[ 3.224000] OV5640 read error!!!!!!!!!!!!!!!
[ 3.228000] ov5640_initialize_ctrls.............1794...........
[ 3.236000] nxp_hdmi_cec_probe success
[ 3.240000] device-mapper: uevent: version 1.0.3
[ 3.244000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 3.252000] Bluetooth: HCI UART driver ver 2.2
[ 3.256000] Bluetooth: HCI H4 protocol initialized
[ 3.260000] DVFS: ASV[2] IDS 24mA, Ro 129 -> Table [IDS 15mA, Ro 130]
[ 3.272000] DVFS: regulator vdd_arm_1.3V
[ 3.272000] DVFS: cpu DVFS with PLL.1 [tables=11]
[ 3.280000] cpuidle: using governor ladder
[ 3.280000] cpuidle: using governor menu
[ 3.284000] Synopsys Designware Multimedia Card Interface Driver
[ 3.292000] dw_mmc dw_mmc.0: Using internal DMA controller.
[ 3.296000] mmc0: no vmmc regulator found
[ 3.300000] dw_mmc dw_mmc.0: Using external card detect irq 267 (io 161)
[ 3.308000] dw_mmc dw_mmc.0: Version ID is 250a
[ 3.312000] dw_mmc dw_mmc.0: DW MMC controller at irq 75, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[ 3.320000] dw_mmc dw_mmc.1: Using internal DMA controller.
[ 3.324000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 3.336000] mmc1: no vmmc regulator found
[ 3.340000] dw_mmc dw_mmc.1: Version ID is 250a
[ 3.344000] dw_mmc dw_mmc.1: DW MMC controller at irq 76, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[ 3.356000] usbcore: registered new interface driver usbhid
[ 3.360000] usbhid: USB HID core driver
[ 3.364000] ashmem: initialized
[ 3.368000] logger: created 256K log 'log_main'
[ 3.372000] logger: created 256K log 'log_events'
[ 3.376000] logger: created 256K log 'log_radio'
[ 3.380000] logger: created 256K log 'log_system'
[ 3.388000] snd pcm: register sound platform 'nxp-pcm'
[ 3.392000] snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287880hz, RFS=256
[ 3.416000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 3.420000] mmc0: new high speed SDHC card at address aaaa
[ 3.424000] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
[ 3.436000] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
[ 3.452000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 3.516000] asoc: ES8316 HiFi <-> nxp-i2s.0 mapping ok
[ 3.516000] spdif-tx: 48000(47999)Hz, MCLK=12287880hz HDMI out
[ 3.524000] asoc: dit-hifi <-> nxp-spdif-tx mapping ok
[ 3.528000] GACT probability NOT on
[ 3.532000] Mirror/redirect action on
[ 3.532000] u32 classifier
[ 3.536000] Actions configured
[ 3.540000] Netfilter messages via NETLINK v0.30.
[ 3.544000] nf_conntrack version 0.5.0 (13469 buckets, 53876 max)
[ 3.552000] ctnetlink v0.93: registering with nfnetlink.
[ 3.556000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.564000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.568000] xt_time: kernel timezone is -0000
[ 3.572000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.580000] arp_tables: (C) 2002 David S. Miller
[ 3.584000] TCP: cubic registered
[ 3.588000] Initializing XFRM netlink socket
[ 3.592000] NET: Registered protocol family 10
[ 3.596000] Mobile IPv6
[ 3.596000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.604000] IPv6 over IPv4 tunneling driver
[ 3.608000] NET: Registered protocol family 17
[ 3.612000] NET: Registered protocol family 15
[ 3.616000] Bluetooth: RFCOMM TTY layer initialized
[ 3.620000] Bluetooth: RFCOMM socket layer initialized
[ 3.624000] Bluetooth: RFCOMM ver 1.11
[ 3.628000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.636000] Bluetooth: BNEP filters: protocol multicast
[ 3.640000] Bluetooth: BNEP socket layer initialized
[ 3.644000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.652000] Bluetooth: HIDP socket layer initialized
[ 3.656000] NET: Registered protocol family 35
[ 3.660000] Registering the dns_resolver key type
[ 3.664000] Registering SWP/SWPB emulation handler
[ 3.672000] axp22_dcdc5: incomplete constraints, leaving on
[ 3.676000] axp22_dcdc4: incomplete constraints, leaving on
[ 3.680000] axp22_dcdc3: incomplete constraints, leaving on
[ 3.688000] axp22_dcdc2: incomplete constraints, leaving on
[ 3.692000] axp22_dcdc1: incomplete constraints, leaving on
[ 3.700000] axp22_dc5ldo: incomplete constraints, leaving on
[ 3.704000] axp22_eldo2: incomplete constraints, leaving on
[ 3.708000] axp22_eldo1: incomplete constraints, leaving on
[ 3.720000] axp22_dldo1: incomplete constraints, leaving on
[ 3.720000] axp22_aldo3: incomplete constraints, leaving on
[ 3.728000] axp22_aldo2: incomplete constraints, leaving on
[ 3.732000] axp22_aldo1: incomplete constraints, leaving on
[ 3.736000] axp22_ldo1: incomplete constraints, leaving on
[ 3.740000] otg_wakelock_init: No USB transceiver found
[ 3.748000] nxp-rtc nxp-rtc.0: setting system clock to 2016-01-01 08:00:01 UTC (1451635201)
[ 3.756000] tmu[0] = trim 44:0, ret 1
[ 3.760000] TMU: register tmu.0 to hwmon (max 1400000khz)
[ 3.764000] ALSA device list:
[ 3.768000] #0: I2S-ES8316
[ 3.772000] #1: SPDIF-Transciever
[ 3.772000] Freeing init memory: 220K
[ 3.776000] Write protecting the kernel text section c0008000 - c0842000
[ 3.784000] rodata_test: attempting to write to read-only section:
[ 3.792000] write to read-only section trapped, success
[ 3.872000] type=1403 audit(1451635201.620:2): policy loaded auid=4294967295 ses=4294967295
[ 3.876000] type=1404 audit(1451635201.624:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[ 4.084000] init: /dev/hw_random not found
[ 4.176000] init: /dev/hw_random not found
[ 4.196000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.196000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.0/by-num/p2,target=/system,type=ext4)=0
[ 4.232000] EXT4-fs (mmcblk0p3): recovery complete
[ 4.232000] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.236000] HDMI HPD State 0x1
[ 4.244000] fs_mgr: check_fs(): mount(/dev/block/platform/dw_mmc.0/by-num/p3,/cache,ext4)=0
[ 4.260000] find cec header!_edid_find_target_cec_address: cec physical address 2000
[ 4.264000] _hdmi_hpd_changed: edid update success, preset 8
[ 4.320000] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/dw_mmc.0/by-num/p3
[ 4.444000] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 4.444000] e2fsck: cache: clean, 11/27392 files, 3535/109568 blocks
[ 4.476000] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 4.480000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.0/by-num/p3,target=/cache,type=ext4)=0
[ 4.512000] EXT4-fs (mmcblk0p7): recovery complete
[ 4.512000] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.520000] fs_mgr: check_fs(): mount(/dev/block/platform/dw_mmc.0/by-num/p7,/data,ext4)=0
[ 4.576000] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/dw_mmc.0/by-num/p7
[ 4.632000] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 4.632000] e2fsck: userdata: clean, 81/158720 files, 38838/624468 blocks
[ 4.660000] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 4.664000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.0/by-num/p7,target=/data,type=ext4)=0
[ 4.692000] setting PHY_BASEADDR_POWER_GATE, set 1
[ 4.692000] setting PHY_BASEADDR_PMU_ISOLATE+4, set 0
[ 4.696000] setting PHY_BASEADDR_PMU_ISOLATE+8, set 0
[ 4.704000] setting PHY_BASEADDR_PMU_ISOLATE, set 1
[ 4.708000] read PHY_BASEADDR_PMU_ISOLATE + 0xC
[ 4.712000] Wait Power UP Ack(powerUpAck=0x00000000)
[ 4.716000] setting ClockGen, set 1
[ 4.720000] setting Reset VR addr(0xf0012008)
[ 4.724000] setting PHY_BASEADDR_VR_PMU addr(0xf0072000)
[ 4.732000] Vr: VR device driver loaded(ver1.2) for s5p6818
[ 4.832000] binder: 123:123 transaction failed 29189, size 0-0
[ 4.912000] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
[ 4.916000] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[ 4.924000] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
[ 4.936000] android_usb: already disabled
[ 4.944000] adb_open
[ 4.944000] mtp_bind_config
[ 4.944000] adb_bind_config
[ 5.020000] logd.auditd: start
shell@nanopi3:/ $ [ 5.840000] healthd: No charger supplies found
[ 5.840000] healthd: No battery devices found
[ 6.116000] ov5640_link_setup
[ 6.116000] camera_common_vin_setup_io
[ 6.116000] ov5640 0-003c: reg_write: i2c write error, reg: 3103
[ 6.120000] ov5640_init: failed to ov5640_write_array init regs
[ 6.128000] ov5640_s_power.............1944...........
[ 6.132000] nxp_hdmi_link_setup: connected to me!!!
[ 10.540000] warning: `main' uses 32-bit capabilities (legacy support in use)
